Category Archives: Woodturning

Give That Man a Cigar (pen)–Part 2

The stabilized cigar halves sat around the house for several days because it rained…and also, the main participant in the project broke his ankle.  Once the boot was installed on his broken pin, and the weather cleared up for a few hours, the cigar pen project was back in play.

craftsbyjennyskip.com drilling out cigar
drilling out the center of the cigar half

First step was to drill out the centers of the cigar pieces, to make room for brass tubes from the pen kit.

craftsbyjennyskip.com sanding pen tubes
sanding the outsides of the brass pen tubes

Next, putting a little “tooth” on the outside surfaces of the brass pen tubes by sanding with 80 grit Abranet, so they adhere better when they’re glued inside the cigar pieces.

craftsbyjennyskip.com gluing pen
gluing up

Next, gluing the brass pen tubes into the drilled-out centers of the cigar pieces.

craftsbyjennyskip.com cigar pen
brass tube is going to fit in this slot
craftsbyjennyskip.com sanding cigar pen
sanding ends of cigar to flush with the brass tubes

The cigar halves, with their glued-in brass tubes, are then sanded on the disk sander until the ends are even with the outer edges of the brass tubes.

craftsbyjennyskip.com turning cigar on a lathe
the cigar halves are then mounted on the lathe and trimmed

The cigar pieces are slid onto a pen mandrel and mounted onto a lathe to be turned and trimmed using a Rockler round carbide mini turning tool.

craftsbyjennyskip.com cigar pen
shaping the cigar pen

Next, many applications of 1) thin CA glue and 2) spray-on accelerator, then sanding with more Abranet from 80 grit to 600 grit.

craftsbyjennyskip.com Abranet
sequence of Abranet from 80 grit to 600 grit
craftsbyjennyskip.com friction polish
application of high friction polish, then glue

After several coats of high-friction polish, then several coats of thick CA glue were applied, to fill in lots of little divots and voids that were chipped out by the turning tool. Even though the cigar was stabilized with resin, it wasn’t completely smooth and rock-hard. It was very chippy. The final finessing step is wet sanding with a series of water-soaked sanding pads in grits 600 to 20,000.

craftsbyjennyskip.com wet sanding pen barrel
wet sanding for the final finessing
craftsbyjennyskip.com pressing pen
pressing the pen parts into place

The rest of the pen parts from the kit are pressed into place.

craftsbyjennyskip.com cigar pen
finished cigar pen

There, a cigar that isn’t bad for your health! Maybe next time we’ll get a Cuban cigar and see if it turns out any different.

Give That Man a Cigar (pen)–Part 1

Not that this was planned to go along with WordPress’s Weekly Photo Challenge: Grid…but there is a grid included in the project…

craftsbyjennyskip.com stabilized cigar
grid inside the vacuum chamber

For more Weekly Photo Challenge: Grid click here.

Not being a cigar smoker, I don’t fully appreciate the culture of cigar smoking but I do have a relative that does. I thought I’d see if I could take a cigar (in this case, one that was made in the Dominican Republic) and make a ball point pen out of it by turning the cigar on a lathe.  In order to accomplish this, I considered two alternatives; stabilize the cigar with some kind of resin or grind up the cigar and mix it with a resin to cast a pen blank.

The option I chose was to stabilize the cigar with resin and use the stabilized cigar as a pen blank.

stabilized cigar parts
stabilized cigar parts after undergoing the treatment listed below

As I prepared for this project I couldn’t help but reflect on the memorable times my family spent visiting Ybor City near Tampa, Florida and eating dinner at the Las Novedades or Columbia restaurants.  I can remember the waiters having fun with my brother and me by seeing just how much Cuban bread we could eat at one sitting.  I can still remember how fantastic that bread tasted once we had lathered it up with (what seemed like) a pound of butter!

The history in this area is steeped in the manufacture of cigars.  I learned that in the cigar factories, a hundred or more (it seemed like that to a 10 year old) Cuban immigrants sat at tables rolling cigars while a man sat at a lectern in the middle of the room reading aloud articles from the newspaper.  Ybor City’s cigar history goes back to the 1880’s.  By the 1930’s there were 150 cigar factories in this area and Tampa was referred to the Cigar Capital of the World. For more history of this era of cigar manufacturing visit Save Cigar City’s page.

Dominican republic cigar
cigar made in Dominican Republic

Taking the cigar, I used the pen kit tubes for the Roadster pen to measure off the lengths of cigar I needed for the pen parts.

Note: If you go to the Craft Supplies web site to check out the link, you may see another link for a “Cigar Pen” kit, too. But don’t be fooled, that kit is for making a pen that faintly resembles the shape of a cigar, not a pen from a real cigar like we’re making here!

I wrapped the cigar at the cut point with blue painters tape to help support the cigar when I cut it into two parts.

prepping cigar for pen kit
cutting the cigar into lengths that will fit the parts from the pen kit

The two cigar sections were then placed in a Turn Tex Woodworks Juiceproof vacuum chamber for the stabilization process. The chamber was supplied with a plastic grid called a pressure fit submersion plate that can be used to anchor the cigar parts in the chamber when the Cactus Juice is added.

vacuum chamber
placing grid on top of cigar parts in vacuum chamber

Enough of the Cactus Juice is added to completely cover the cigar parts with an additional inch or so to allow for the Cactus Juice to ultimately be absorbed by the cigar parts.

adding Cactus Juice to vacuum chamber
pouring the Cactus Juice into the chamber

The lid is then placed on the chamber and the chamber is connected to a vacuum pump.  As the vacuum pump runs, it evacuates air from the chamber and the voids of the cigar parts.  As the air leaves the voids, you can see the Cactus Juice “boil” as the air bubbles up through the resin.

bubbling
bubbling in the chamber

After about 20 minutes, the bubbles stop, indicating that most of the air has been removed from the cigar samples. The vacuum is then released and the cigar parts are allowed to soak in the Cactus Juice for about 20 minutes.

Following this soaking period, the cigar parts are wrapped individually in aluminum foil and then baked at 220 degrees F for two hours.  

cigars stabilized with Cactus Juice
stabilized cigar pieces ready to go in the oven

Next post: Part 2, turning the stabilized cigar on the lathe and turning it into a pen…